- 您现在的位置：买卖IC网 > Sheet目录317 > CAT24C512HU5IGT3 (ON Semiconductor)IC EEPROM SRL 512KB I2C 8UDFN
CAT24C512
WRITE OPERATIONS
Byte Write
In Byte Write mode the Master sends a START, followed
by Slave address, two byte address and data to be written
(Figure 6). The Slave acknowledges all 4 bytes, and the
Master then follows up with a STOP, which in turn starts the
internal Write operation (Figure 7). During internal Write,
the Slave will not acknowledge any Read or Write request
from the Master.
Page Write
The CAT24C512 contains 65,536 bytes of data, arranged
in 512 pages of 128 bytes each. A two byte address word,
following the Slave address, points to the first byte to be
written. The most significant 9 bits (A 15 to A 7 ) identify the
page and the last 7 bits identify the byte within the page. Up
to 128 bytes can be written in one Write cycle (Figure 8).
The internal byte address counter is automatically
incremented after each data byte is loaded. If the Master
Acknowledge Polling
Acknowledge polling can be used to determine if the
CAT24C512 is busy writing or is ready to accept commands.
Polling is implemented by interrogating the device with a
‘Selective Read’ command (see READ OPERATIONS).
The CAT24C512 will not acknowledge the Slave address,
as long as internal Write is in progress.
Hardware Write Protection
With the WP pin held HIGH, the entire memory is
protected against Write operations. If the WP pin is left
floating or is grounded, it has no impact on the operation of
the CAT24C512. The state of the WP pin is strobed on the
last falling edge of SCL immediately preceding the first data
byte (Figure 9). If the WP pin is HIGH during the strobe
interval, the CAT24C512 will not acknowledge the data byte
and the Write request will be rejected.
Delivery State
The CAT24C512 is shipped erased, i.e., all bytes are FFh.
transmits more than 128 data bytes, then earlier bytes will be
overwritten by later bytes in a ‘wrap ? around’ fashion
(within the selected page). The internal Write cycle starts
immediately following the STOP.
http://onsemi.com
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CAT24C512XI
IC EEPROM I2C SRL 512KB 8SOIC
CAT24C64ZI-GT3
IC EEPROM I2C SRL 64KB 8MSOP
CAT24M01XI
IC EEPROM I2C SRL 1MB 8SOIC
CAT24M01YI-GT3
IC EEPROM SRL 1MB I2C 8TSSOP
CAT25010LI-G
IC EEPROM 1KBIT 10MHZ 8DIP
CAT25020VE-GT3
IC EEPROM 2KB I2C SER SPI 8SOIC
CAT25128XI
IC EEPROM 128KB SPI SER 8SOIC
CAT25160HU4I-GT3
IC EEPROM SRL 16KB I2C 8UDFN
相关代理商/技术参数
CAT24C512LI-G
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器
RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512WI-G
制造商:ON Semiconductor 功能描述:512KB I2C SER EEPROM - Rail/Tube 制造商:ON Semiconductor 功能描述:EEPROM 512KB I2C SER EEPROM 制造商:ON Semiconductor 功能描述:TUBE / 512KB I2C SER EEPROM
CAT24C512WI-GT3
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512XI
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512XI-T2
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器
RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512YI-G
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512YI-GT3
功能描述:电可擦除可编程只读存储器 512KB I2C SER 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C512YIGT3JN
功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8